1
/* -*- mode: c++; compile-command: "BOARD=pro5v make"; -*- */
5
* Copyright (C) 2011 Tim Marston <tim@ed.am> and Dan Marston.
4
* Copyright (C) 2011 Tim Marston <edam@waxworlds.org>
7
6
* This file is part of propeller-clock (hereafter referred to as "this
8
* program"). See http://ed.am/dev/software/arduino/propeller-clock for more
7
* program"). See http://ed.am/software/arduino/propeller-clock for more
11
10
* This program is free software: you can redistribute it and/or modify
22
21
* along with this program. If not, see <http://www.gnu.org/licenses/>.
25
/******************************************************************************
29
* a PC fan is wired up to a 12V power supply
31
* the fan's SENSE (tachiometer) pin connected to pin 2 on the
34
* the pins 4 to 13 on the arduino should directly drive an LED (the
35
LED on pin 4 is in the centre of the clock face and the LED on pin
38
* if a longer hand (and a larger clock face) is desired, pin 4 can be
39
used to indirectly drive a transistor which in turn drives several
40
LEDs that turn on anf off in unison in the centre of the clock.
42
* a button should be attached to pin 3 that grounds it when pressed.
44
* A DS1307 remote clock is connected via I2C on analog pins 4 and 5.
46
Implementation details:
48
* for a schematic, see ../project/propeller-clock.sch.
50
* the timing of the drawing of the clock face is recalculated with
51
every rotation of the propeller.
53
* a PC fan actually sends 2 tachiometer pulses per revolution, so the
54
software skips every other one. This means that the clock may
55
appear upside-down if started with the propeller in the wrong
56
position. You will need to experiment to dicsover the position that
57
the propeller must be in when starting the clock.
61
* pressing the button cycles between variations of the current
64
* pressing and holding the button for a second cycles between display
65
modes (e.g., analogue and digital).
67
* pressing and holding the button for 5 seconds enters "time set"
68
mode. In this mode, the following applies:
69
- the field that is being set flashes
70
- pressing the button increments the field currently being set
71
- pressing and holding the button for a second cycles through the
72
fields that can be set
73
- pressing and holding the button for 5 seconds sets the time and
76
******************************************************************************/
81
#include "mode_switcher.h"
84
24
//_____________________________________________________________________________
100
40
static unsigned long segment_step_sub_step = 0;
101
41
static unsigned long segment_step_sub = 0;
104
static Button button( 3 );
107
static int major_mode = 0;
110
static std::vector< MajorMode * > major_modes;
112
47
//_____________________________________________________________________________
116
// check for button presses
51
// ISR to handle the pulses from the fan's tachiometer
52
void fanPulseHandler()
120
int event = button.update();
125
major_modes[ major_mode ]->short_press();
128
major_modes[ major_mode ]->long_press();
131
if( ++major_mode >= major_modes.size() )
133
major_modes[ major_mode ]->activate();
54
// the fan actually sends two pulses per revolution. These pulses
55
// may not be exactly evenly distributed around the rotation, so
56
// we can't recalculate times on every pulse. Instead, we ignore
57
// every other pulse so timings are based on a complete rotation.
58
static bool ignore = true;
62
// set a new pulse time
63
new_pulse_at = micros();
139
// draw a display segment
68
// draw a particular segment
140
69
void drawNextSegment( bool reset )
142
// keep track of segment
144
static int segment = ( NUM_SEGMENTS - CLOCK_SHIFT ) % NUM_SEGMENTS;
145
if( reset ) segment = ( NUM_SEGMENTS - CLOCK_SHIFT ) % NUM_SEGMENTS;
147
static int segment = NUM_SEGMENTS - 1 - CLOCK_SHIFT;
148
if( reset ) segment = NUM_SEGMENTS - 1 - CLOCK_SHIFT;
152
Drawer &drawer = major_modes[ major_mode ]->get_drawer();
153
if( reset ) drawer.draw_reset();
154
drawer.draw( segment );
157
if( ++segment >= NUM_SEGMENTS ) segment = 0;
159
if( --segment < 0 ) segment = NUM_SEGMENTS - 1;
71
static unsigned int segment = 0;
72
if( reset ) segment = 0;
75
for( int a = 0; a < 10; a++ )
76
digitalWrite( a + 4, ( ( segment >> a ) & 1 )? HIGH : LOW );
195
111
// work out the time that this segment should be displayed until
196
112
end_time += segment_step;
197
segment_step_sub += segment_step_sub_step;
198
if( segment_step_sub >= NUM_SEGMENTS ) {
199
segment_step_sub -= NUM_SEGMENTS;
113
semgment_step_sub += semgment_step_sub_step;
114
if( semgment_step_sub >= NUM_SEGMENTS ) {
115
semgment_step_sub -= NUM_SEGMENTS;
208
// ISR to handle the pulses from the fan's tachiometer
209
void fanPulseHandler()
211
// the fan actually sends two pulses per revolution. These pulses
212
// may not be exactly evenly distributed around the rotation, so
213
// we can't recalculate times on every pulse. Instead, we ignore
214
// every other pulse so timings are based on a complete rotation.
215
static bool ignore = true;
219
// set a new pulse time
220
new_pulse_at = micros();
233
132
for( int a = 4; a < 14; a++ )
234
133
pinMode( a, OUTPUT );
236
// set up mode-switch button on pin 3
238
digitalWrite( 3, HIGH );
239
button.add_event_at( 5, 1 );
240
button.add_event_at( 1000, 2 );
241
button.add_event_at( 4000, 3 );
244
136
Serial.begin( 9600 );
246
// set up major modes
247
static ModeSwitcher mode_switcher;
248
major_modes.push_back( &mode_switcher );
249
major_modes[ 0 ]->activate();
256
143
// if there has been a new pulse, we'll be resetting the display
257
144
bool reset = new_pulse_at? true : false;
259
// only do this stuff at the start of a display cycle, to ensure
260
// that no state changes mid-display
266
// keep track of time
267
Time &time = Time::get_instance();
271
146
// draw this segment
272
147
drawNextSegment( reset );
added
removed
propeller-clock/propeller-clock.pde
