/elec/propeller-clock : revision 4

1

Why can't I use a potentiometer to get a different voltage?

2

===========================================================

3

4

Suppose that you have 12V and you need 6V. Why can't you use an

5

arrangement like this to get your 6Vs?

6

7

+12V -------+---------

8

|

9

|¯|

10

|_| R

11

|

12

+--------o 6V, yes?

13

|

14

|¯|

15

|_| R

16

|

17

GND -------+---------

18

19

You *do* get 6V, but it isn't actually practical to do this. The

20

problem is that, when R is suitably high, you've limited the current

21

at the 6V pin so much that it isn't really useful.

22

23

And when R is suitably low, there isn't enough resistance between the

24

+12V and GND rails to prevent a lot of current flowing. Lets work

25

this out (lets suppose that R is 1 ohm).

26

27

V = IR, therefor I = V/R

28

P = VI = V(V/R) = (V^2)/R = ( 12 ^ 2 ) / 1 = 144W

29

P = VI, therefor I = P/V = 144/12 = 12A

30

31

That's a lot of current and a lot of power, flowing continuously, just

32

to provide 6V!

33

34

Also, fluctuations in resistance and current drawn on the 6V pin would

35

actually change the ratio of the potentiometer, so you wouldn't get 6V

36

anyway.

37

38

The solution is to use a voltage regulator. The 7805 will give out 5V

39

(so long as you can supply it with at least 7V). But the arduinos

40

already have something similar on-board and they can take an input

41

voltage in the range 6-20V (although 7-12V is recommended).

42

43

44

Wiring up multiple LEDs in series to a single arduino pin

45

=========================================================

46

47

First, lets think about a single LED.

48

49

|

50

Arduino | ___ ,,

51

o-----|___|-----►|---- GND

52

| R D

53

|

54

55

The arduino pin, when raised high, is at 5V and no more than 20mA can

56

be taken from it. The LED will take about 10mA and wants about 1.5V.

57

58

You can think of this as a potentiometer arrangement, with the

59

resistance of R and D proportionally splitting the voltage between the

60

two components. We want 1.5V across the LED, so we need 3.5V (that's

61

5 - 1.5) across the resistor. Now, we don't know the resistance of

62

the LED, but we don't need to. If we know that we want 10mA through

63

the whole series (the resistor and the diode), then we can use V=IR as

64

follows...

65

66

V=IR, therefore R=V/I

67

R = 3.5 / .01 = 350Ω

68

69

Which is why the standard resistor you'd use with one LED is orange,

70

orange, brown (actually, 340 ohms).

71

72

Now lets consider more than one LED in series.

73

74

|

75

Arduino | ___ ,, ,,

76

o-----|___|-----►|-----►|---- GND

77

| R D1 D2

78

|

79

80

Ok, so now you still need 10mA through the whole series, but you want

81

1.5V across the first diode and 1.5V across the second as well. That

82

leaves 2V across R, the resistor (5 - 1.5 - 1.5).

83

84

R = V/I = 2 / .01 = 200Ω

85

86

You can see that beyond three or perhaps, at a push, four LEDs you're

87

not going to get the required 1.5V across each LED. So three (or four)

88

is the limit to how many LEDs you can drive in series from one pin on

89

the arduino.

90

91

92

Wiring up multiple LEDs in parallel to a single arduino pin

93

===================================--======================

94

95

Image we have

96

97

|

98

Arduino | ___ ,,

99

o-----|___|---+---►|---.

100

| R | D1 |

101

| | |

102

| | ,, |

103

| '---►|---+--- GND

104

| D2

105

106

This wouldn't work. We can't use one resistor in series with the two

107

LEDs because the resistance of the two LEDs wont actually be exactly

108

the same. You'll end up running one brighter than the other and burn

109

one out quicker.

110

111

So, imagine we have this instead

112

113

|

114

Arduino | ___ ,,

115

o----+---|___|----►|---.

116

| | R1 D1 |

117

| | |

118

| | ___ ,, |

119

| '---|___|----►|---+--- GND

120

| R2 D2

121

122

This is ok. R1 and R2 are just the usual 340 ohms. But we have to

123

bare in mind that each LED requires 10mA. So the total current drawn

124

from the arduino pin will be 20mA, which is the most you're allowed to

125

draw. So two LEDs is the most that we can drive, in parallel, directly

126

from a pin.

127

128

129

Using a transistor to drive multiple LEDs

130

=========================================

131

132

In both of the following diagrams, the resistor on the arduino pin,

133

R1, just needs to be something suitably high to provide a small

134

current on the base of the transistor. So, R1 could be 1kΩ.

135

136

Here's an "in series" set up

137

138

.----- 12V

139

|

140

|¯|

141

|_| R2

142

|

143

|

144

▼ D1

145

¯``

146

|

147

| |

148

| ▼ D2

149

| ¯``

150

| |

151

| |

152

| ▼ D3

153

| ¯``

154

| |

155

Arduino | ___ ,-|

156

o----|___|--(|< ) T

157

| R1 `-|

158

| |

159

| '----- GND

160

161

This is fine. D1, D2 and D3 will require a total of 4.5V across them

162

(1.5V each), leaving plenty of headroom (you've got 12V to play with).

163

R2 would be

164

165

R2 = V/I = ( 12 - 1.5 - 1.5 - 1.5 ) / 0.01 = 750Ω

166

167

So the limit here is about 8 LEDs.

168

169

Something else to consider here is that the transistor actually also

170

requires 0.7V across it. So in that calculation, the desired voltage

171

across R2 should actually be 12 - 1.5 - 1.5 - 1.5 - 0.7, but we can

172

safely ignore it in this example.

173

174

Here's an "in parallel" set up

175

176

.-------+-------+----- 12V

177

| | |

178

|¯| |¯| |¯|

179

|_| R3 |_| R4 |_| R5

180

| | | |

181

| | | |

182

| ▼ D1 ▼ D2 ▼ D3

183

| ¯`` ¯`` ¯``

184

| | | |

185

| +-------+-------'

186

| |

187

Arduino | ___ ,-|

188

o----|___|--(|< )

189

| R1 `-|

190

| |

191

| '----- GND

192

193

Here, R3 = R4 = R5 = 340Ω, as usual. The numbher of LEDs is limited

194

only by the current that can be drawn from the power supply.