/elec/quadcopter

To get this branch, use:
bzr branch http://bzr.ed.am/elec/quadcopter

« back to all changes in this revision

Viewing changes to src/rc-interface/receiver.cc

  • Committer: dan
  • Date: 2014-04-15 02:32:34 UTC
  • Revision ID: dan-20140415023234-xd7x37vepkavc8u1
Made a couple of minor adjustments to the circuet diagram. Joined up some of the GND pins to allow more flexability in designing the pcb.

Show diffs side-by-side

added added

removed removed

src/rc-interface/receiver.cc
 
1
//
 
2
// receiver.cc
 
3
//
 
4
 
 
5
 
 
6
#include "receiver.h"
 
7
#include "config.h"
 
8
#include "common.h"
 
9
#include <Arduino.h>
 
10
 
 
11
 
 
12
// channel sequence order
 
13
static const int channel_order_[] = { CHANNEL_ORDER };
 
14
 
 
15
// set to the time of the last pulse edges
 
16
static unsigned long new_pulse_up_[2] = { 0, 0 };
 
17
static unsigned long new_pulse_down_ = 0;
 
18
static char new_pulse_interrupt_;
 
19
 
 
20
 
 
21
// ISR to handle the PPM signals
 
22
inline void signal_handler( int interrupt, int pin )
 
23
{
 
24
        // record rising/falling edge
 
25
        if( digitalRead( pin ) )
 
26
                new_pulse_up_[ interrupt ] = micros();
 
27
        else {
 
28
                new_pulse_down_ = micros();
 
29
 
 
30
                // record which interrupt just had a falling edge
 
31
                new_pulse_interrupt_ = interrupt;
 
32
        }
 
33
}
 
34
 
 
35
 
 
36
static void signal_handler_0()
 
37
{
 
38
        signal_handler( 0, 2 );
 
39
}
 
40
 
 
41
 
 
42
static void signal_handler_1()
 
43
{
 
44
        signal_handler( 1, 3 );
 
45
}
 
46
 
 
47
 
 
48
void Receiver::setup()
 
49
{
 
50
        // set up an interrupts
 
51
        attachInterrupt( 0, signal_handler_0, CHANGE );
 
52
        attachInterrupt( 1, signal_handler_1, CHANGE );
 
53
        digitalWrite( 2, LOW );
 
54
        digitalWrite( 3, LOW );
 
55
}
 
56
 
 
57
 
 
58
bool Receiver::read_channels( int channel_values[] )
 
59
{
 
60
        static unsigned long last_pulse_down = 0;
 
61
        static int next_channel = 0;
 
62
 
 
63
        // capture pulse values atomically
 
64
        noInterrupts();
 
65
        unsigned long pulse_up = new_pulse_up_[ (int)new_pulse_interrupt_ ];
 
66
        unsigned long pulse_down = new_pulse_down_;
 
67
        char new_pulse_interrupt = new_pulse_interrupt_;
 
68
        interrupts();
 
69
 
 
70
        // if the amount of time that has passed since the last falling edge is
 
71
        // greater than the frame gap, reset the next channel so that we can start
 
72
        // reading them again
 
73
        if( next_channel &&
 
74
                new_pulse_interrupt == 1 &&
 
75
                calculate_duration( pulse_down, micros() ) > MIN_FRAME_GAP_WIDTH )
 
76
        {
 
77
                // reset the next channel (which restarts reading them)
 
78
                next_channel = 0;
 
79
        }
 
80
 
 
81
        // check for a new complete pulse
 
82
        if( pulse_down != last_pulse_down )
 
83
        {
 
84
                // are there still pulses to read?
 
85
                if( next_channel < NUM_CHANNELS )
 
86
                {
 
87
                        unsigned long duration =
 
88
                                calculate_duration( pulse_up, pulse_down );
 
89
 
 
90
                        // does this pulse look ok?
 
91
                        if( duration >= MIN_PULSE_WIDTH &&
 
92
                                duration <= MAX_PULSE_WIDTH )
 
93
                        {
 
94
                                // store channel value
 
95
                                int channel = channel_order_[ next_channel ] - 1;
 
96
                                channel_values[ channel ] = MAX_CHANNEL_VALUE *
 
97
                                        ( duration - MIN_PULSE_WIDTH ) /
 
98
                                        ( MAX_PULSE_WIDTH - MIN_PULSE_WIDTH );
 
99
 
 
100
                                // we got a channel
 
101
                                next_channel++;
 
102
                        }
 
103
                        else {
 
104
                                // set invalid channel number (to indicate error)
 
105
                                next_channel = NUM_CHANNELS + 1;
 
106
                        }
 
107
                }
 
108
 
 
109
                last_pulse_down = pulse_down;
 
110
        }
 
111
 
 
112
        // if we've read a frame, invalidate the frame (so we don't report it a
 
113
        // second time) and return true
 
114
        if( next_channel == NUM_CHANNELS ) {
 
115
                next_channel++;
 
116
                return true;
 
117
        }
 
118
        
 
119
        return false;
 
120
}